Can't sleep so here's a question I'm just going to rip from a Gearpage thread that no one responded to as I have exactly the same concern:As we know the vintage fuzzes (or vintage circuits in new fuzzes) don't play nice with a buffer in front.My plan is to set up an overdrive pedal chain and a fuzz pedal chain.Can anyone speak to the buffer + fuzzes thing with the LS-2?The pedal (LS-2) has input and output jacks, and send/return jacks for loops A and B. The incoming signal is buffered, then split three ways: to the output mixer/buffer, to loop A send and loop B send. If left empty, the send/return jack in each loop are connected internally, to simply pass the signal along. Each loop has a level control, located after the return jack. The return signals then join the main bypass signal in the output mixer/buffer, and is then sent out through the output jack. https://www.thegearpage.net/board/index ... z.2037693/In my case I want to run a Rat in parallel with an EQD soundshank, which is a great buzzaround clone.

Nate Dort wrote:It looks like there's a mistake in that schematic. There's no output from the first preamp tube.Yes there is. Its the .01uF cap that goes back to the inout jacks to cascade gain stages. Like a 2204/2203 style thing.Anyway, to my ears the topology looks very 60's/70's Fender, but with that additional gain stage up front. Plugged in to the low gain jack it's kinda Super Reverb-y lookin.

I have a novice-style amp question!My main amp for a short while has been a Garnet Jammer. It's kind of peculiar and there isn't a ton of info about it floating around. Besides this circuit.1. Is there a real cursory overview someone could give me based on the circuit topology? Just like oh it's kind of like x Fender amp with y thing different about it2. Mainly what has me trippin is the interplay between the two preamps (like w/ the higher-gain input). I would love to understand what's going on there. That is what I am doing this post about.3. I dug up a picture of the back of my own personal amp, which is at the practice space right now, and I'm noticing for the first time a Solo Pre-Set control (upper right)? What on earth is that. Amp has a two preamp gain controls and a master volume on the front, what else is even left for that knob to be.Thank you!

It looks like there's a mistake in that schematic. There's no output from the first preamp tube.That Solo Level knob looks like it's just an extra foot-switchable volume control,

Dr Tony Balls wrote:Nate Dort wrote:It looks like there's a mistake in that schematic. There's no output from the first preamp tube.Yes there is. Its the .01uF cap that goes back to the inout jacks to cascade gain stages. Like a 2204/2203 style thing.Ah, yeah, I see it now. I don't know jack shit about Marshalls, never worked on one.

Yeah I realized mine only goes up to 250 DCV. Fuck that I quit. I ve pulled chassis out of a few amps with no problem, why does Gibson make you use tools inside there.Edit: found a set of insulated nut drivers for about $20. Will tackle again later.

Where can I use a volt meter to make sure the charge is drained from this 50s GA-40 amp? It doesn t have 12ax7 in the preamp so I can t use the first pin in v1. I need to change out the speaker in this bitch and the screws and nuts to pull the chassis are located inside the chassis because why wouldn t they be?http://imgur.com/ozCPOF3http://imgur.com/GA60Z9W

I think it was listed online, but the store it was at is a few blocks away from me so I stumbled across it IRL. Sorry homie!

Mason wrote:I think it was listed online, but the store it was at is a few blocks away from me so I stumbled across it IRL. Sorry homie!thats much cooler, well found! Glad its your main squeeze, garnets for everyone! as minor input, it looks like the added gain stage is maybe on a switched jack so its disconnected if not plugged in - just a note if you ever have to replace that jack

That s an even better idea - I bought a full set out of frustration getting an ampeg Gemini chassis out and they come in useful all the time