current DIY projects you are working on .. or planning on.

91
tarandfeathers wrote:Very cool. Who did your laser engraving, Prodigy Engineering?Yeah, although they had a bit of trouble getting the engraving to line up with the holes I pre-drilled. Normally I would drill the holes after the engraving process, but I was afraid of tearing up the finish on the large holes for the meters. I had to strip it, repaint and have them laser it again. Long story, but it was kind of a headache and they tried to put the blame on me. I've been happy with the work they've done for me up until now, but this experience really turned me off to using them again.

current DIY projects you are working on .. or planning on.

93
PEPPER! wrote:practice/recording room in the basement. not strictly DIY as I'm paying people who actually know what they're doing for carpentry, drywall, and electricity, and will have plenty of help with the floors/setup/logistics from Jim & Matt E. I'm doing any grunt work & soldering myself. it's exciting - I would much rather dick around with this all day than do work. there 28 channels of mic/line running through the wall to points around the room, 4 headphone lines, and speaker wire, all of it will terminate on a patch panel in the corner. finished the space will measure about 8 1/2' by 17 1/2' and 7 1/2' at the highest point in the ceiling. I'll post some more pictures as it shapes up.Nice.I really wish I would have taken the time to run cables in the same manner as you are planning. I mean fuck, I built the damn walls. Too stoned probably. My snake runs to my "control room" via a hole in the closet ceiling, speaker cables, and mic cables everywhere.

current DIY projects you are working on .. or planning on.

96
Rodabod wrote:japmn wrote:It would be perfect for our keys rig accept that after about 3 minutes, it starts getting a humming sound and if you touch the volume knob, it crackles at full volume. CKTCKTHTKCHTCK!Physically touching the metal shaft (ooh err), or rotating the knob at all?The latter suggests unwanted DC on the pot. The former suggests possibly a bad earth.It buzzes if you dont touch anything at all. Once it starts buzzing, if you turn the volume knob, it crackles loudly. Also the output is very distorted while in buzz time and clean when it isn't buzzing. It doesn't seem to react to physically touching it like other ground buzzes.If I get some time, I'll record it and post a little sample.

current DIY projects you are working on .. or planning on.

97
B\_M\_L wrote:I started work on the neck for my acoustic this week.I found out that I m not totally shit at wood work “ which was my biggest fear in starting this thing. It is early days though.So far, I ve just taken the rough sawn Mahogany block and planed it square. Then made a cut for the neck/headstock scarf joint. And I ve planed the surface of the join. Next step “ glue!PICS PICS PICS PICS PICS

current DIY projects you are working on .. or planning on.

100
like 4 years ago, I posted a bunch about a Jagmaster project I was doing, trying to put a 25.5 neck on one of the 24 inch model bodies. It was going to require redrilling the necks I had, in addition to probably redrilling and moving the bridge about 3/8, and I kinda put it on the back burner. I recently picked up a Mighty Mite tele neck to replace the uncomfortable neck on my squier tele custom, but it needs drilled, so in the interim, I decided to try the MIM strat neck I had forgotten was sitting around for the Jagmaster, and I love so the strat neck in the tele, so I think I'm leaving it that way.Since I need to drill the Mighty Mite neck anyways, I realize I might as well use it for the jagmaster, so that is my new project. My friend who shares my practice space has a drill press, so I'm hoping he'll help me drill the neck, and then I'll move onto figuring out the bridge. I pulled the strings off the saddle screws, thinking I may just barely get enough room to intonate the 25.5 neck by setting the saddles way back and maybe grinding a couple down by a mm or so... but I'm going to get the neck installed, and then worry about whether to move the bridge or not. I have some Fender tuners on the way from reverb.I also will have to put some sort of lacquer or finish on the neck too, so I'll have to figure out that whole process at some point.
Image

Who is online

Users browsing this forum: No registered users and 0 guests